![\"25-5134221](\"https:\/\/ever-powers.com\/wp-content\/uploads\/2026\/08\/25-5134221-Tractor-Power-Steering-Cylinder.webp\" "\\"\\"")
<\/div>\n25-5134221 Tractor Power Steering Cylinder \u2014 55 mm Bore \u00d7 232 mm Stroke High-Force OEM Agricultural Steering Ram<\/h2>\n
| OEM Part Number<\/td>\n | 25-5134221<\/td>\n<\/tr>\n |
| Bore Diameter<\/td>\n | 55 mm<\/td>\n<\/tr>\n |
| Rod Diameter<\/td>\n | 25 mm<\/td>\n<\/tr>\n |
| Stroke<\/td>\n | 232 mm<\/td>\n<\/tr>\n |
| Mounting Distance (C-C)<\/td>\n | 385 mm<\/td>\n<\/tr>\n |
| Cylinder Type<\/td>\n | Double-Acting, Single Body<\/td>\n<\/tr>\n |
| Seal Material<\/td>\n | PU Primary + NBR Backup<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n \n Enquire for OEM or Distributor Supply<\/p>\n 55 mm bore \u00b7 232 mm stroke \u00b7 385 mm C-C \u00b7 Ships FOB Ningbo<\/p>\n<\/div>\n<\/div>\n<\/div>\n Engineering Overview: 25-5134221 Long-Stroke 55 mm Bore Tractor Power Steering Cylinder for Heavy Front Axle Load Applications<\/h2>\nThe 25-5134221 Tractor Power Steering Cylinder<\/strong> is defined by a distinctive dimensional combination: a 55 mm bore paired with a 25 mm rod and a 232 mm stroke, producing a stroke-to-bore ratio of 4.2:1 and an unusually high stroke-to-C-C ratio of 0.60. The 55 mm bore is the first step above the standard 50 mm bore class and delivers meaningfully higher force output\u2014approximately 28.5 kN extension force at 12 MPa, compared to 23.6 kN from a 50 mm bore at the same pressure. This additional steering force is the primary reason the design authority specified a 55 mm bore on this chassis: the target tractor carries a heavier front axle static load\u2014typically from a front loader attachment or ballast weights\u2014that requires greater hydraulic force to initiate wheel rotation from a stationary or near-stationary position on firm soil.<\/p>\n The 385 mm C-C is moderate for a 232 mm stroke cylinder, producing the highest stroke-to-C-C ratio of any single-body cylinder in this 12-product series (0.60). This means the cylinder traverses 60% of its total installed length on each full steering manoeuvre, which demands particular attention to rod buckling behaviour and wiper seal contamination management. The part number prefix “25-5134221″ follows the same numeric convention as the 22-5142046 (Product 5), confirming both products originate from the same tractor manufacturer’s bill of materials\u2014”25” likely designates a different chassis series within the same brand family.<\/p>\n<\/div>\n <\/p>\n <\/p>\n <\/p>\n Bore area is 2,376 mm\u00b2; rod area is 491 mm\u00b2 (25 mm rod). The bore-to-rod area ratio is 4.84:1\u2014the second-highest in this series after Product 5’s 5.16:1. At 12 MPa, extension force is 28.5 kN and retract force is 22.6 kN. The critical concern is the 25 mm rod at 232 mm stroke: the rod slenderness ratio under fixed-pinned end conditions is approximately 89, placing it within the Euler buckling regime. The theoretical Euler buckling load is approximately 35 kN\u2014only 1.23\u00d7 the extension force at rated pressure. This safety factor is below the 1.5\u00d7 minimum generally recommended for dynamic steering applications. In practice, the bracket geometry and the axle articulation constraints prevent the rod from reaching its theoretical free-column buckling length, but fleet maintenance managers should be aware that any modification to the axle bracket geometry\u2014such as welding reinforcement plates that change the effective rod end-condition\u2014could alter the buckling behaviour. Replacement with a non-OEM cylinder using a smaller rod diameter is explicitly not recommended for this application.<\/p>\n Barrel tube: 20# seamless precision steel, bore honed to Ra \u2264 0.4 \u00b5m. The 55 mm bore diameter requires a dedicated 55 mm honing stone and air plug gauge; confirm that the supplier operates dedicated 55 mm tooling rather than re-boring a 50 mm barrel, which produces inferior bore geometry. Rod: 45# carbon steel, induction hardened to 55\u201360 HRC, chrome plated to 20\u201325 \u00b5m, ground to h6 tolerance. Seal kit: PU piston U-ring, NBR O-ring secondary, PU rod U-seal, reinforced PU wiper seal. The reinforced wiper is specified here due to the long 232 mm stroke exposure length and the proximity of the cylinder to the front loader attachment zone on target machines, where hydraulic oil drips from loader hose connections can contaminate the wiper lip and reduce its effective service life.<\/p>\n Clevis pin bore diameter is 22 mm H7 at both ends, matching the 22f7 standard pin used across several compact-to-mid Chinese tractor front axle designs. Despite the larger 55 mm bore, the clevis pin spec reverts to 22 mm rather than stepping up to 25 mm or 28 mm\u2014a design choice reflecting that the lateral clevis loading on this chassis is within the 22 mm pin’s shear capacity at the rated steering force. For OEM cross-reference, the minimum verification parameter set is: 55 mm bore, 25 mm rod, 232 mm stroke, 385 mm C-C, 22 mm clevis pin. Any third-party equivalent claiming to replace this cylinder must satisfy all five parameters; a 50 mm bore substitute will produce approximately 17% less extension force, which may be adequate for unloaded operation but will produce noticeable steering effort increase with a front loader or ballast weights fitted.<\/p>\n Torque clevis pin retention fasteners to 35\u201340 N\u00b7m. Port connections are M16\u00d71.5; torque to 55\u201365 N\u00b7m with new bonded seals. Before finalising the installation, manually cycle the cylinder rod through its full 232 mm stroke by hand (hoses disconnected) to verify smooth, friction-free travel without binding\u2014a bind at any point in the stroke indicates axle bracket misalignment that must be corrected before hydraulic connection. Bleed the circuit with six full lock-to-lock cycles at low idle; the larger 55 mm bore displaces 549 cm\u00b3 per full extension stroke, requiring additional bleed cycles versus smaller bore models to fully purge air. Seal inspection at 500-hour intervals; complete seal kit replacement at 2,000 hours standard or 1,200 hours in loader-intensive or abrasive conditions.<\/p>\n Proof test: 21 MPa static for 5 minutes per stroke direction; 10 dynamic cycles at rated pressure. Internal leakage acceptance criterion: \u22643 mL\/min at the piston seal (increased from the 50 mm bore class limit to account for the larger piston seal circumference). Chrome rod batches tested per ASTM B117 at 240 hours \/ 5% NaCl \/ 35\u00b0C. Barrel exterior: two-component epoxy primer, full weld-seam coverage. MOQ: 10 units; standard pallet quantity: 40 units. Lead time: 7\u201312 working days FOB Ningbo for standard stock; 25\u201330 days for custom specifications. Custom options include 28 mm rod upgrade (eliminates buckling concern for heavy-loader applications), alternative port thread standards, and FKM seals. OEM white-label packaging and documentation available in English, Spanish, and Portuguese.<\/p>\n Specify your tractor model, front loader fitment status, and required quantity. Our engineering team confirms bore and rod selection suitability for your axle load before order confirmation.<\/p>\n MOQ: 10 units \u00a0|\u00a0 Lead time: 7\u201312 days FOB \u00a0|\u00a0 28 mm rod upgrade option available<\/p>\n<\/div>\n<\/div>\n <\/p>","protected":false},"excerpt":{"rendered":" High-force OEM steering ram for front-loader-equipped tractors. 55mm bore, 25mm rod, 232mm stroke, 385mm C-C. 28.5kN extension force. Reinforced wiper seal, FOB Ningbo.<\/p>","protected":false},"featured_media":1559,"template":"","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":""},"product_brand":[],"product_cat":[112],"product_tag":[],"class_list":["post-1574","product","type-product","status-publish","has-post-thumbnail","product_cat-tractor-hydraulic-cylinder","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/product\/1574","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/media\/1559"}],"wp:attachment":[{"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/media?parent=1574"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/product_brand?post=1574"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/product_cat?post=1574"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/ever-powers.com\/fr\/wp-json\/wp\/v2\/product_tag?post=1574"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}} |
![\"Agricultural](\"https:\/\/ever-powers.com\/wp-content\/uploads\/2026\/08\/Agricultural-tractor.webp\" "\\"\\"")
<\/p>\n